Scientific Principles and Technique of Optical Fabrication Processes

Cover
Title Page
Copyright
DECLARATION
ABOUT THE EDITOR
TABLE OF CONTENTS
List of Contributors
List of Abbreviations
Preface
SECTION I: INTRODUCTION TO OPTICAL FABRICATION PROCESSES
	Chapter 1 Design and Fabrication of Fiber-Optic Nanoprobes for Optical Sensing
		Abstract
		Introduction
		Experimental Procedures
		Results and Discussion
		Conclusion
		Acknowledgements
		References
	Chapter 2 Materials Development for Next Generation Optical Fiber
		Abstract
		Introduction
		Results and Discussion
		Experimental Section
		Conclusions
		Acknowledgments
		Author Contribution
		References
	Chapter 3 Fabrication of Fresnel Plates on Optical Fibres By Fib Milling For Optical Trapping, Manipulation and Detection of Single Cells
		Abstract
		Introduction
		Fabrication And Optical Characterization
		Discussion
		Discussion
		Conclusions
		References
	Chapter 4 Review on Fabrication Technologies for Optical Mold Inserts
		Abstract
		Introduction
		Fabrication Methods
		Form-Giving Technologies
		Micro-Structuring Technologies
		Summary and Discussion
		Author Contributions
		References
SECTION II: SURFACE POLISHING PROCESSES
	Chapter 5 Research Progress of Optical Fabrication and Surface-Microstructure Modification of SiC
		Abstract
		Introduction
		Optical Fabrication of Silicon Carbide
		Surface Modification
		Conclusion
		Acknowledgments
		References
	Chapter 6 Experimental Optimization of Annular Polishing Parameters for Silicon Carbide
		Abstract
		Introduction
		Analytical Investigation of Annular Polishing
		Annular Polishing Experiment of RB-SIC
		Summary
		Authors’ Contributions
		Acknowledgments
		References
	Chapter 7 Effects of Process Parameters on Material Removal in Vibration-Assisted Polishing of Micro-Optic Mold
		Abstract
		Introduction
		Experimental Setup and Conditions
		Analysis of Pressure And Tool Wear Effects
		Results and Discussions
		Conclusions
		Author Contributions
		Acknowledgments
		References
SECTION III: SUBSURFACE DAMAGES
	Chapter 8 Methods for Detection of Subsurface Damage: A Review
		Abstract
		Introduction
		Mechanisms of Subsurface Damage Formation
		Destructive Methods
		Non-Destructive Methods
		Other Methods
		Discussion
		Summaries and Outlook
		Authors’ Contributions
		References
	Chapter 9 Influence of Cutting Speed on Subsurface Damage Morphology and Distribution in Ground Fused Silica
		Abstract
		Introduction
		Materials And Methods
		Results
		Discussion
		Conclusions
		Author Contributions
		References
	Chapter 10 Subsurface Damage in Polishing Process of Silicon Carbide Ceramic
		Abstract
		Introduction
		Theoretical Analysis
		Numerical Simulation
		Validation of Experimental Results
		Conclusions
		Acknowledgments
		Author Contributions
		References
SECTION IV: SURFACE ROUGHNESS
	Chapter 11 Surface Roughness Evaluation Based on Acoustic Emission Signals in Robot Assisted Polishing
		Abstract
		Introduction
		Experimental Procedure
		Results
		Conclusions
		Acknowledgments
		Author Contributions
		References
	Chapter 12 Interfacial Surface Roughness Determination by Coherence Scanning Interferometry using Noise Compensation
		Abstract
		Introduction
		Theory
		Computer Simulation
		Discussion
		Conclusions
		Acknowledgment
		References
	Chapter 13 Effect of Slurry Composition on the Chemical Mechanical Polishing of thin Diamond Films
		Abstract
		Introduction
		Experimental Procedure
		Results and Discussion
		Conclusions
		Acknowledgements
		References
SECTION V: LASER DAMAGE RESISTANCE
	Chapter 14 Laser Damage Resistance of Polystyrene Opal Photonic Crystals
		Abstract
		Introduction
		Results and Discussion
		Methods
		Conclusions
		References
	Chapter 15 Surface Molecular Structure Defects And Laser-Induced Damage Threshold of Fused Silica During A Manufacturing Process
		Abstract
		Introduction
		Results and Disscusion
		Lidts
		Conclusions
		Methods
		References
	Chapter 16 Impact of the Polishing Suspension Concentration on Laser Damage of Classically Manufactured and Plasma Post-Processed Zinc Crown Glass Surfaces
		Abstract
		Introduction
		Materials And Methods
		Results
		Discussion
		Conclusions
		Author Contributions
		Acknowledgments
		References
Index
Back Cover