Impedance source power electronic converters

Content: Title Page 
 Copyright Page
 Contents
 Preface
 Acknowledgment
 Bios
 Chapter 1 Background and Current Status
 1.1 General Introduction to Electrical Power Generation
 1.1.1 Energy Systems
 1.1.2 Existing Power Converter Topologies
 1.2 Z-Source Converter as Single-Stage Power Conversion System 
 1.3 Background and Advantages Compared to Existing Technology
 1.4 Classification and Current Status
 1.5 Future Trends
 1.6 Contents Overview
 Acknowledgment
 References
 Chapter 2 Voltage-Fed Z-Source/Quasi-Z-Source Inverters 
 2.1 Topologies of Voltage-Fed Z-Source/Quasi-Z-Source Inverters 2.2 Modeling of Voltage-Fed qZSI 2.2.1 Steady-State Model 
 2.2.2 Dynamic Model
 2.3 Simulation Results
 2.3.1 Simulation of qZSI Modeling
 2.3.2 Circuit Simulation Results of Control System
 2.4 Conclusion
 References
 Chapter 3 Current-Fed Z-Source Inverter 
 3.1 Introduction
 3.2 Topology Modification
 3.3 Operational Principles
 3.3.1 Current-Fed Z-Source Inverter 
 3.3.2 Current-Fed Quasi-Z-Source Inverter 
 3.4 Modulation
 3.5 Modeling and Control
 3.6 Passive Components Design Guidelines
 3.7 Discontinuous Operation Modes 3.8 Current-Fed Z-Source Inverter/Current-Fed Quasi-Z-Source Inverter Applications 3.9 Summary
 References
 Chapter 4 Modulation Methods and Comparison
 4.1 Sinewave Pulse-Width Modulations 
 4.1.1 Simple Boost Control
 4.1.2 Maximum Boost Control
 4.1.3 Maximum Constant Boost Control
 4.2 Space Vector Modulations
 4.2.1 Traditional SVM
 4.2.2 SVMs for ZSI/qZSI
 4.3 Pulse-Width Amplitude Modulation 
 4.4 Comparison of All Modulation Methods
 4.4.1 Performance Analysis
 4.4.2 Simulation and Experimental Results
 4.5 Conclusion
 References Chapter 5 Control of Shoot-Through Duty Cycle: An Overview 5.1 Summary of Closed-Loop Control Methods 
 5.2 Single-Loop Methods 
 5.3 Double-Loop Methods 
 5.4 Conventional Regulators and Advanced Control Methods
 References
 Chapter 6 Z-Source Inverter: Topology Improvements Review 
 6.1 Introduction
 6.2 Basic Topology Improvements
 6.2.1 Bidirectional Power Flow
 6.2.2 High-Performance Operation 
 6.2.3 Low Inrush Current
 6.2.4 Soft-Switching 
 6.2.5 Neutral Point
 6.2.6 Reduced Leakage Current
 6.2.7 Joint Earthing
 6.2.8 Continuous Input Current
 6.2.9 Distributed Z-Network 6.2.10 Embedded Source6.3 Extended Boost Topologies
 6.3.1 Switched Inductor Z-Source Inverter 
 6.3.2 Tapped-Inductor Z-Source Inverter 
 6.3.3 Cascaded Quasi-Z-Source Inverter 
 6.3.4 Transformer-Based Z-Source Inverter 
 6.3.5 High Frequency Transformer Isolated Z-Source Inverter 
 6.4 L-Z-Source Inverter 
 6.5 Changing the ZSI Topology Arrangement
 6.6 Conclusion
 References
 Chapter 7 Typical Transformer-Based Z-Source/Quasi-Z-Source Inverters 
 7.1 Fundamentals of Trans-ZSI 
 7.1.1 Configuration of Current-Fed and Voltage-Fed Trans-ZSI