Reinforced Cement Concrete Structures

Cover
Half Title
Title
Copyright
Dedication
Contents
Preface
Acknowledgments
About the author
Chapter 1 Introduction
	1.1 Introduction
	References
Chapter 2 Soil and foundation
	2.1 Introduction
	2.2 Engineering properties of soil
	2.3 Geotechnical investigation tests and properties of soil
	2.4 Selection of type of foundation
	2.5 Protection of foundation against subsoil corrosion
	References
Chapter 3 Structural concrete
	3.1 Grade of concrete and application
	3.2 Materials and admixtures
	3.3 Method of construction document
	References
Chapter 4 Codes and standards
	4.1 Notes on design and construction
	4.2 Reference list of codes and standards
Chapter 5 Workout examples by ACI and IS Code method
	5.1 Design of piles – bored and driven
		5.1.1 Driven pile in clay
		5.1.2 Driven pile in sand
		5.1.3 Bore pile in layered soil
	5.2 Design of pile caps
		5.2.1 Pile cap for 3 pile group
		5.2.2 Pile cap for 4 pile group
		5.2.3 Pile cap for 5 pile group
		5.2.4 Pile cap for 6 pile group
		5.2.5 Pile cap for 16 pile group
		5.2.6 Pile group patterns
	5.3 Design of isolated footing
		5.3.1 Flat footing
		5.3.2 Sloped footing
	5.4 Design of combined footing
	5.5 Design of Raft foundation
		5.5.1 Turbine generator foundation raft of soil
		5.5.2 Circular raft on the pile
	5.6 Design of the beam
	5.7 Design of column
	5.8 Design of the slab
	5.9 Design of earth retaining wall
	5.10 Design of cable trench
	5.11 Design of the ground floor slab
	5.12 Design of a culvert
	5.13 Design charts
	References
Chapter 6 Construction details and reinforcement placement
	6.1A Beam Reinforcement – Sheet 1
	6.1B Beam Reinforcement – Sheet 2
	6.2 Column Reinforcement
	6.3A Slab Reinforcement – Plan and Section
	6.3B Slab Reinforcement around openings
	6.4 Stair case slab
	6.5 Wall reinforcement
	6.6 Pile cap reinforcement
	6.7 Construction Joints in Slab
	6.8 Expansion Joints
	6.9 Crack Control Joints
	6.10 Separation Joints
	6.11 Cable Trench
	6.12A Manholes and Pits – Sheet 1
	6.12B Manholes and Pits – Sheet 2
	6.13 Surface Drains
	6.14 Box Culvert
	6.15A Embedded Plate – Sheet 1
	6.15B Embedded Plate – Sheet 2
	6.15C Embedded Plate – Sheet 3
	6.16 Anchor bolts
	6.17 Edge protection detail around curb and opening
	6.18 Grating and Chequered plate floor support
	6.19 Protection of Foundation from Subsoil corrosion
	6.20 Pre-stressed Concrete Pile
	References
Chapter 7 Design of a large water reservoir on ground
	7.1 Description of structure
	7.2 Reference codes and standards
	7.3 Materials used
	7.4 Design parameters
	7.5 Sketches
	7.6 Roof Slab
	7.7 Side walls
	7.8 Base raft
	7.9 Settlement
	7.10 Construction drawing
	References
Chapter 8 Design of a two-story office building on soft soil
	8.1 Description of building
	8.2 Reference codes and standard
	8.3 Material used
	8.4 Load and load combinations
	8.5 Structural analysis and member design
		8.5.1 Analytical model (STAAD)
		8.5.2 STAAD input command file
		8.5.3 Foundation design
		8.5.4 Member design
	8.6 Construction drawing
	References
Index