Proceedings of the International Conference on Aerospace System Science and Engineering 2023 (Lecture Notes in Electrical Engineering, 1153)

Contents
Investigation into Provisions and Validation for Cockpit Smoke Evacuation on Civil Aircraft
	1 Introduction
	2 CCAR25.831(d) Regulation
	3 25.831(d) Regulation Interpretation
	4 Validation for CCAR25.831(d)
	5 Test Configuration and Devices
	6 Test Results and Analysis
	7 Conclusion
	References
SysML-Based Approach for Functional Quantitative Modeling of Civil Aircraft Systems
	1 Introduction
	2 Flow and General Functional Modeling
		2.1 Flow Model Establishment
		2.2 The Structure of General Functional Model
		2.3 The State of General Functional Model
		2.4 The Behavior of General Functional Model
	3 Hierarchical Functional Models
		3.1 The Structure of Hierarchical Functional Model
		3.2 The State of Hierarchical Functional Model
		3.3 The Behavior of Hierarchical Functional Model
	4 Case Study
		4.1 Introduction of Elevator Surface Control System
		4.2 Establishment of Flow Models and Sub-level Functional Models of the Elevator Surface Control System
		4.3 Establishment of Hierarchical Functional Model of Elevator Surface Control System
		4.4 Simulation of Hierarchical Functional Model of Elevator Surface Control System
	5 Conclusion
	References
Research on MagicGrid-Based Requirements Development Process of Flight Control System
	1 Introduction
	2 Overview of the MagicGrid Method
	3 System-Level Requirements Development
		3.1 Black Box Modeling
		3.2 White Box Modeling
	4 Component-Level Requirements Development
		4.1 System-Level Modeling
		4.2 Component-Level Modeling
	5 Discussion
	6 Conclusion
	References
Airport Collaborative Decision-Making in Single Pilot Operations of Commercial Aircraft
	1 Introduction
	2 A-CDM in Dual-Pilot Operation Mode
		2.1 A-CDM System Architecture
		2.2 Information Sharing
		2.3 Milestone Method
	3 A-CDM in Single Pilot Operations Mode
		3.1 Single Pilot Operations Mode
		3.2 Decision Process Organization of Single Pilot Operation
		3.3 SPO-A-CDM
	4 Modelling and Analysis
		4.1 Simulation Platform
		4.2 Model-Based Simulation Analysis
	5 Conclusion
	References
Research on Capability Catalog Generation of UAV Intelligent System Based on DoDAF
	1 Introduction
	2 Application Scenario Modeling and Demand Analysis of UAV Intelligent System
	3 Multi-View Requirement Analysis Method Based on DoDAF
		3.1 Basic Requirement Acquisition
		3.2 Task Activity Acquisition
		3.3 Unit Organization Relationship Acquisition
		3.4 System Activity Decomposition
		3.5 System Resource Flow Identification
	4 UAV Intelligent System Capability Catalog Generation
	5 UAV Intelligent System Capability Catalog Generation
	References
Research on the Contribution Rate of Shipboard Manned/Unmanned Aerial Vehicle Cooperative Operation Based on Wargame Data Mining
	1 Introduction
	2 Evaluation Process of Contribution Rate of Shipboard Manned/Unmanned Aerial Vehicle Cooperative System
		2.1 Constructing a Static Model Based on DoDAF
		2.2 Dynamic Deduction Based on Wargame
		2.3 Data Mining of Shipboard Manned/Unmanned Aerial Vehicle Cooperative Operation Mode
	3 Realization of Data Mining Algorithm
		3.1 Closed Frequent Pattern Mining
		3.2 Algorithm Flow
	4 Experimental Verification
		4.1 Scenario Description
		4.2 Simulation Result Analysis
	5 Conclusion
	References
Cooperative Organization and Application Mechanism Based on Intention Environment Target for Maritime Ship-Aircraft Cooperation
	1 Introduction
	2 Intent, Environment, and Target Requirements and Concepts
		2.1 Requirements for Modern Ship-Aircraft Cooperative Mode
		2.2 Decision-Making Mode of Ship and Aircraft Cooperative Process
		2.3 Decision-Making Mode of Ship and Aircraft Cooperative Process
		2.4 Collaborative Decision-Making Model Based on Intention, Environment and Objectives
	3 Operational Mechanism and Composition of Coordinated Decision-Making in the Process
		3.1 Operational Mechanism of Coordinated Organization
		3.2 Operational Organization of Operational Coordinated Decision-Making
		3.3 Operational Collaborative Decision-Making Target System
		3.4 Phases of Operational Coordinated Decision-Making
		3.5 Operational Collaborative Decision-Making Mode Mechanism
	4 Scenario Modeling and Analysis
	5 Conclusion
	References
LPV Robust Filter Based Fault Diagnosis Method for Aeroengine Control System
	1 Introduction
	2 Multi-sensor Information Fusion
		2.1 Theoretical Background
		2.2 Description of the Problem
	3 Fault Diagnosis Based on LPV Robust Filters
	4 Experiment and Discussion
	5 Conclusion Experimental Verification
	References
A Research on the Intelligent Flight Deck Development Trend for the Civil Aircraft
	1 Introduction
	2 Characteristics of Electrified Cockpit (The First Stage)
	3 Characteristics of Informative Cockpit (The Second Stage)
	4 Latest Technologies and Research Status
	5 Development Trend of Intelligent Cockpit (The Third Stage)
	6 Development Route
	7 Apply Strategies and Recommendations
	8 Conclusion
	References
Angle of Attack of the Aircraft Calibration
	1 Introduction
	2 Installation Position for AOA Sensor
	3 Flight Test Methods for Calibrating AOA
		3.1 Fuselage-Nose-Boom Method
		3.2 Attitude Angle or Attitude-Flight-Path Angle Method
	4 Conclusion
	References
Influence of Radius of Microphone Array on Virtual Rotating Array Beamforming for Rotating Noise Source Localization
	1 Introduction
	2 Statement of the Problem
		2.1 VRA Beamforming and Deconvolution Algorithm
		2.2 Influence of Radius of Microphone Array
	3 Simulation Setup
	4 Simulation Results
	5 Conclusions
	References
A Finite Element Method of Research on Transverse Mechanical Properties of Fiber-Reinforced Composites with Random Matrix Void Defects
	1 Introduction
	2 Computational Micromechanical Model
		2.1 Random Matrix Void Finite Element Model
		2.2 Material Properties
		2.3 Mesh
	3 Periodical Boundary Condition
	4 Results
		4.1 Transverse Tension
		4.2 Transverse Compression
		4.3 Transverse Shear
	5 Conclusion
	References
A Review of Some Key Issues in CFD-Based Throughflow Simulation
	1 Introduction
	2 Three Throughflow Methods
		2.1 Stream Function Method
		2.2 Streamline Curvature Method
		2.3 CFD-Based Throughflow Method
		2.4 Several Issues of CFD-Based Throughflow Method
	3 Leading and Trailing Edge Discontinuity Models
		3.1 Automatic Incidence Correction Model
		3.2 Momentum Flux Discontinuity Model
		3.3 Actuator Disk Model
		3.4 Arbitrary Discontinuity Breakdown Model
	4 Deviation and Losses in CFD-Based Throughflow
		4.1 Modeling of Deviation Angle and Losses
		4.2 Novel Method to Develop Empirical Model
	5 Conclusion
	References
Influence of Multiple Parameters on the Efficiency of a Single Nozzle in a Heavy Gas Turbine Combustor
	1 Introduction
	2 Experimental Facility
	3 Result Analysis
		3.1 Performance Analysis of Peripheral Nozzle
		3.2 Performance Analysis of Peripheral Nozzle
	4 Conclusions
	References
Analysis of the Influence of Total Pressure Error on Air Data Calibration
	1 Introduction
	2 Air Data Measurement and Calibration Method
	3 Total Pressure Error and Its Influence on Air Data System Calibration
	4 Example Analysis
	5 Conclusion
	References
Analysis of Impact Properties of Nanocomposites at Micron Scale
	1 Introduction
	2 Nano Impact Simulation
		2.1 SPH Simulation Geometry Model
		2.2 Simulation of Material Models
	3 Analysis of Numerical Simulation Results
	4 Analysis of Results and Theoretical Analysis
		4.1 Analysis of Results
		4.2 Analysis of the Impact Process
	5 Conclusion
	References
Simulation Research on Air Distribution Optimization of Civil Aircraft Cabin Ventilation System
	1 Introduction
	2 Air Distribution Simulation Model of Cabin Ventilation System
		2.1 Simulation Model of Non-standard Air Resistance Components
		2.2 Build Simulation Models
		2.3 Model Validation
	3 Simulation and Results Analysis
		3.1 Simulation Procedure
		3.2 Results Analysis
	4 Conclusion
	References
Investigation of the 2-D Distribution Form of Bearing Stress in a Single-Bolt Single-Shear Metal-Composite Hybrid Joint
	1 Introduction
	2 Theoretical Basis of the Analysis
		2.1 Derivation of the Bearing Stress Distribution
		2.2 Statical Method Used
	3 Modeling and Testing
		3.1 Test Set-Ups
		3.2 Finite Element Modeling
		3.3 Model Validation
	4 Analysis Results
		4.1 Analysis Matrix
		4.2 The Effect of Layup Sequences (L)
		4.3 The Effect of Layup Thickness (S)
		4.4 The Effect of Thickness Ratio (T)
		4.5 The Effect of Clamping Force (F)
	5 Conclusion
	References
The Impact of Bleeding Slot Angles on the Performance of a Compressor
	1 Introduction
	2 Numerical Methods
		2.1 Mesh Independence
	3 The Impact of Bleeding Slot Angles on the Overall Performance of the Compressor
	4 The Impact of Bleeding Slot Angles on the Partial Performance of the Compressor
	5 Conclusion
	References
Numerical Investigation of Diffuser Curvilinear Meridional Shape on Centrifugal Compressor Stage Performance
	1 Introduction
	2 Baseline Compressor
	3 Centrifugal Compressor Numerical Modelling Validation
		3.1 Numerical Investigation Set-Up
		3.2 NASA HECC Model Validation
	4 Vaned Diffuser and Exit Guide Vane Optimization
	5 Conclusion
	References
Modeling Method of Specimen Repair Techniques from Polymer Composite Material
	1 Introduction
	2 Damage Types and Repair Methods
		2.1 Adhesive Bonded External Repair
		2.2 Mechanically Fastened External Doubler
		2.3 Stepped (Overlapping) Repair
	3 Finite Element Analysis
		3.1 Finite Element Analysis of Adhesive Bonded External Repair
		3.2 Finite Element Analysis of Mechanically Fastened External Doubler
		3.3 Finite Element Analysis of Stepped (Overlapping) Repair
	4 Analysis and Compare of Results
	5 Conclusion
	References
Process Approach as a Tool of the Knowledge-Intensive Industry Organization Management System
	1 Introduction
	2 Why Process Approach
		2.1 PLAN
		2.2 DO
		2.3 CHECK
		2.4 ACT
	3 Classification of Processes
	4 Conclusion
	References
Author Index