Proceedings of the 2nd International Conference on Advanced Surface Enhancement (INCASE 2021): Innovation Leading to Industrialization (Lecture Notes in Mechanical Engineering)

Preface
Contents
Advanced in Surface Engineering
Surface Modification of Inconel 718 by Robot-Guided Centrifugal Finishing and Vibratory Finishing
	1 Introduction
	2 Materials and Methods
	3 Results and Discussion
	4 Conclusion
	References
Advanced Surface Enhancement of a High Strength Aluminum Alloy Through Friction Stir Processing
	1 Introduction
	2 Experimental Procedure
	3 Results and Discussion
	4 Conclusion
	References
Vibratory Finishing of Laser Powder Bed Fused Stainless Steel 316 Internal Cooling Channels
	1 Introduction
	2 Vibratory Finishing Methodology
		2.1 Workpiece and Measurement Methodology
		2.2 Media and Equipment
	3 Results and Discussion
		3.1 Experimental Results
		3.2 Simulation
	4 Conclusion
	References
Rapid and Stable Plasma Transformation of Polyester Fabrics for Highly Efficient Oil-Water Separation
	1 Introduction
	2 Methodology
	3 Results and Discussion
	4 Conclusion
	References
Influence of Wettability of Micro-nano Structured Lead Bronze on Friction Properties
	1 Introduction
	2 Methods
	3 Results and Discussion
	4 Conclusion
	References
Effect of Ablative Layer Thickness on Laser Shock Peening Process Intensity
	1 Introduction
	2 Methodology
		2.1 Almen Strip and Arc Height Deflection Measurement
		2.2 Laser Shock Peening Trials
	3 Results and Discussion
	4 Conclusions
	References
Fatigue Strength Improvement Effect of AZ31 Alloy by Multi-stage Wet Blasting
	1 Introduction
	2 Experimental Method
		2.1 Materials and Specimens
		2.2 Wet Blasting Conditions
		2.3 Various Experimental Methods
	3 Result and Discussion
		3.1 Fatigue Strength Test Results
		3.2 Hardness Measurement Result
		3.3 Residual Stress Measurement Result
		3.4 Surface Roughness Measurement Result
	4 Conclusions
	References
Deep Cold Rolling (DCR) as Potential Surface Enhancement Process for Mold Inserts and Cores
	1 Introduction
	2 Methodology
	3 Results and Discussion
	4 Conclusions
	References
Wettability and Spectrum Characteristics of Ti6Al4V Alloy Surface Based on Femtosecond Laser Texturing Technology
	1 Introduction
	2 Methods
	3 Results and Discussion
	4 Conclusions
	References
Effect of Overlap in Robotic Hammer Peening on the Surface Integrity of Alloy Steel 4142
	1 Introduction
	2 Experimental Setup and Methodology
	3 Results and Discussion
		3.1 Surface Hardness
		3.2 Residual Stress
	4 Conclusions
	References
Determination of the Interaction Depth Caused by Stress Peening at Leaf Springs
	1 Introduction
	2 Basics of Stress Peening Springs
	3 Experimental Setup
		3.1 Leaf Spring Sample
		3.2 Residual Stress Determination
		3.3 Peening Procedure
	4 Results
	5 Conclusion
	References
New Electronic Peening Intensity Measurement Sensor Almen Intensity Correlation and Time Variation Study
	1 Introduction
	2 Sensor Description and Capabilities
	3 Correlation Between Sensor Output and Almen Intensity
	4 Intensity Variation Over Time
	5 Conclusion
	References
Fatigue Enhancement of Ti-6Al-4V via Ex-situ Warm-Shot-Peening (WSP)
	1 Introduction
	2 Methods
	3 Results and Discussion
	4 Conclusion
	References
The Research of Surface Roughness Prediction with Machine Learning According to Process Parameters in Laser Powder Bed Fusion
	1 Introduction
	2 Methodology
	3 Results
	4 Conclusion
	References
Low-Temperature Atmospheric Pressure Plasma for Applications in Flexible and Printed Electronics
	1 Introduction
	2 Methods
		2.1 Plasma Treatment
	3 Results and Discussion
	4 Conclusion
	References
Preparation for Metallic Composite Material with High Surface Strength-Corrosion Resistance
	1 Introduction
	2 Experimental Method
		2.1 Hot-Compressing Bonding
		2.2 High-Temperature Heat Treatment
	3 Result and Discussion
		3.1 Chemical Composition and Porosity
		3.2 Micro-hardness and Corrosion-Resistance Analysis
	4 Conclusion
	References
Surface and Subsurface Characterisation
Novel Interpretation of Volta Potential Measurements from In-Situ SKPFM for Localised Corrosion Analysis in Aluminium Alloys
	1 Introduction
	2 Methods
	3 Discussions
		3.1 Classical Interpretation of Volta Potential Measurements (from Ex-Situ SKPFM)
		3.2 Novel Interpretation of Volta Potential Measurements (from In-Situ SKPFM)
	4 Conclusions
	References
Minerals Disorder Determination in Special Cases of Metastatic Bone Due to Breast Cancer Using LIBS Technique
	1 Introduction
	2 Material and Method
		2.1 Serum Samples
		2.2 LIBS Setup
		2.3 LIBS Parameters
	3 Results and Discussion
	4 Conclusion
	References
Correlation Study Between Barkhausen Noise and Depth-Resolved Residual Stress Upon Shot Peening
	1 Introduction
	2 Materials and Methods
	3 Experimental Results and Discussion
		3.1 Barkhausen Noise Depth-Frequency Computation
		3.2 Barkhausen Noise Data Collection
	4 Conclusion
	References
Application of Phase and Crystallographic Orientation Mapping for Materials Characterization
	1 Introduction
	2 Methods
	3 Results and Discussion
	4 Conclusion
	References
Damage Assessment of Helicoidal CFRP Using Active Infrared Thermography
	1 Introduction
	2 Methods
	3 Results and Discussion
	4 Conclusion
	References
In Situ High Temperature XRD Studies of Molten Natural CMAS Corrosion on Thermal Barrier Coatings
	1 Introduction
	2 Material and Methods
	3 Results and Discussion
		3.1 Phase Evolution and Microstructure of CMAS-TBC
		3.2 Phase Evolution and Microstructure of CMAS-TBC
	4 Conclusion
	References
Effect of Build Angle on Surface Roughness of High-Speed Selective Laser Melted Ti-6Al-4V Alloy
	1 Introduction
	2 Methods
	3 Results and Discussion
	4 Conclusion
	References
A Method of Dynamic Active Infrared Thermography to Reduce Inspection Time of CFRP Components
	1 Introduction
	2 Methodology
		2.1 Material Characterization
		2.2 Experiment Setup
	3 Results and Discussion
		3.1 Static Active IRT
		3.2 Dynamic Active IRT
	4 Conclusion
	References
Determining Subsurface Defects’ Depth in CFRP Composites Using Lock-In Thermography
	1 Introduction
	2 Methods
	3 Results and Discussion
	4 Conclusion
	References
Surface Coatings
Electrochemistry and Engineering Study of Molecular Protective-Films to Steel-Alloys
	1 Introduction
	2 Methods
	3 Results and Discussion of DOE Study on REMs-Ligands
		3.1 Raman Spectrum of Ce 3-Hnp and AS1020 Steel-Alloy Coupons
	4 Conclusion
	References
Prediction of Microstructure Evolution of Cold Sprayed Coatings Using a Dislocation Density Based Constitutive Model
	1 Introduction
	2 Methods
	3 Results and Discussion
	4 Conclusion
	References
Parameters Optimization for Laser Cladding Fe55 Alloy on 40Cr Steel
	1 Introduction
	2 Methods
		2.1 Materials
		2.2 Equipment and Methods
	3 Results and Discussion
	4 Conclusion
	References
Feasibility Tests on Directed Laser Deposition and Cold Spray Coatings Applied in Series for Different Industrial Applications
	1 Introduction
	2 Methods
	3 Results and Discussion
	4 Conclusions
	References
Advanced Surface Engineering and Protective Coating
	1 Introduction
	2 Surface Engineering
		2.1 Cold-Working
		2.2 Laser Treatment
	3 Protective Coating
		3.1 Laser-Cladding
		3.2 Twin-Wire Arc Spray (TWAS)
	4 Conclusion and Outlook
	References
Development of Dry Lubricant Nickel-MoS2 Composite Through Brush Plating
	1 Introduction
	2 Experimental
	3 Results and Discussions
	4 Conclusions
	References
Effects of Spray Angle on Mass, Thickness, Porosity & Residual Stress in Cold-Sprayed Ti-6Al-4V Coatings
	1 Introduction
	2 Methods
	3 Results and Discussion
	4 Conclusion
	References
Corrosion and Mechanical Behavior of Plasma Electrolytic Oxidation Coated Al Alloy
	1 Introduction
	2 Methods
	3 Results and Discussion
	4 Conclusion
	References
Effectiveness of Cold Spray Coating on Cast Iron to Prevent Oxidation
	1 Introduction
	2 Methods
		2.1 Cold Spray Process
		2.2 Materials Characterization
	3 Results and Discussion
	4 Conclusions
	Reference
Cold Spray Coatings for Surface Enhancement of Inconel 718
	1 Introduction
	2 Methods
		2.1 Cold Spray Process
		2.2 Characterization
	3 Results and Discussion
	4 Conclusions
	References
Evaluation of Powders for Cold Spray Coatings Through Study of Single Particle Impact
	1 Introduction
	2 Methods
		2.1 Cold Spray Process
		2.2 Material Characterization
	3 Results and Discussion
	4 Conclusions
	Reference
Post-processing of Cold Spray Coatings via Rapid Induction Heating
	1 Introduction
	2 Methods
		2.1 Cold Spray Process
		2.2 Induction Heating
		2.3 Materials Characterization
	3 Results and Discussion
	4 Conclusions
	References
Corrosion Resistance of Unsealed Plasma Sprayed Coating Under Two Different Accelerated Exposures
	1 Introduction
	2 Methods
	3 Results and Discussion
	4 Conclusions
	References
High Performance Cool Coatings
	1 Introduction
	2 Results and Discussion
	3 Conclusion
	References
Influences of Porosity on the In-Vitro Cell Responses of Cold Sprayed Ti-Ta Composites
	1 Introduction
	2 Methods
		2.1 Fabrication of Porous Structures
		2.2 In-Vitro Biocompatibility
	3 Results and Discussion
		3.1 Cell Response to the Polished Surfaces with Moderate and Low Porosity
		3.2 Surface Potential Measurement on Cold Sprayed Ti-Ta Composite
	4 Conclusions
	References
Modification of Cold Sprayed CoCrMo Alloy Coatings via Laser Shock Peening
	1 Introduction
	2 Materials and Methods
	3 Results and Discussions
	4 Conclusions
	References
Feedstock Characteristics Effect on Cold Sprayability of Tantalum Coatings
	1 Introduction
	2 Materials and Methods
	3 Results and Discussions
	4 Conclusions
	References
NoVOC Water-Borne Coatings Through Utilization of the Nano-confinement Effect
	1 Introduction
	2 Methods
	3 Results and Discussion
	4 Conclusion
	References
Modelling and Simulation
Calibration of a Continuum-Based Granular Flow Dynamics Model for the Numerical Simulation of the Stream Finishing Process
	1 Introduction
	2 Methods
		2.1 Continuum – Based Granular Flow Dynamics Modelling Approach
		2.2 Numerical simulation set-up
		2.3 Experimental Set - up
	3 Results and Discussion
	4 Conclusions
	References
FDTD Simulation of the Spectral Characteristics of the Secondary Array Nanostructures on the Material Surface
	1 Introduction
	2 Simulation and Result Analysis
	3 Conclusion
	References
A Simple Waviness Evolution Model for the Stream Finishing Process
	1 Introduction
	2 Methods
		2.1 Waviness Evolution Model
		2.2 Experimental Set-up
		2.3 Simulation Set-up
	3 Results and Discussion
	4 Conclusions
	References
A PID Model Based Controller for Automated Shot Peening Processes
	1 Introduction
	2 Methodology
		2.1 Process Model and Proxy Model
		2.2 Control Framework Development
	3 Results and Discussion
	4 Conclusions
	References
Phase-Field Crystal Modelling of Deformation Behavior in Grain Growth
	1 Introduction
	2 PFC Simulation Process
	3 Simulation Result and Discussion
	4 Conclusions
	References
Design Consideration for Additively Manufactured Components Through Topology Optimization and Generative Design for Weight Reduction
	1 Introduction
	2 Methods
		2.1 Part Screening Methodology
	3 Results and Discussion
		3.1 Part Consolidation and Generative Design
		3.2 Design Consideration and Surface Finishing
	4 Conclusion
	References
Simulation Study on High Order Harmonic Generation by Ultra-intense Laser Driven Grating Targets
	1 Introduction
	2 Methods
	3 Results and Discussions
	4 Conclusion
	References
Development of Shot Peening Coverage Evaluation Model from 3D Topography Analysis on Ti-6Ai-4V
	1 Introduction
	2 Experimental Methods
	3 Experimental Results and Discussions
	4 Conclusions
	References
Effect of Coefficients of Restitution on the Particle Dynamics in Cold Spray and Shot Peening
	1 Introduction
	2 Methods
		2.1 Experimental Settings and Measurement
		2.2 Modelling and Data Evaluation
	3 Results and Discussion
		3.1 Effect of COR on Particle In-Flight Behavior in Cold Spray
		3.2 Effect of COR on Particle In-Flight Behavior in Shot Peening
	4 Conclusions
	References
Toolpath Planning for Cold Spray Additive Manufacturing
	1 Introduction
	2 Spray Strategies for CSAM
	3 Tool Path Planning for CSAM
	4 Conclusions
	References
Computational Fluid Dynamics Simulation of Cold Spray Process for Particle Velocity Investigation
	1 Introduction
	2 Numerical Method
	3 Results and Discussion
	4 Conclusion and Future Works
	References
Analysis of Glass Transition Temperature Shifts Induced by Internal and External Plasticizers in (Meth)acrylate Polymer Coatings with Molecular Simulations
	1 Background
	2 Results
	3 Conclusion
	References
Automatic Mirror Polishing of Rough, Freeform AM Surfaces Using a Toolpath Generation Framework
	1 Introduction
	2 Methodology
	3 Experimental Setup and Trials
	4 Results and Discussions
	5 Conclusion
	References
Author Index