NUMISHEET 2022: Proceedings of the 12th International Conference and Workshop on Numerical Simulation of 3D Sheet Metal Forming Processes (The Minerals, Metals & Materials Series)

Contents
Part I  Numerical Implementation of Advanced Constitutive Models
1  A New Trial Stress for Newton's Iteration Based on Plastic Strain Rate Potential
2  Anisotropic Time-Dependent Continuum Damage-Coupled Plasticity Model for Predicting Ductile Fracture of 6xxx Series Aluminum Alloys
3  Characterization of Impurities in Nanomaterials
4  Constructing Exact Solutions to Modelling Problems
5  Crystal Plasticity Modelling of Localization in Precipitation Hardened AA6060
6  Deformation and Fracture in Micro-stamping Process
7  Die Design for Flashless Forging of a Polymer Insulator Fitting
8  DP1180 Material Calibration Between Sheet Metal Simulation and Prototype
9  Evolution of the R-value and Its Determination Based on Reverse Fitting for Sheet Metal
10  Modelling Transient Mechanical Behavior of Aluminum Alloy During Electric-Assisted Forming
11  Numerical Prediction of Failure in Single Point Incremental Forming Using a New Yield Criterion for Sheet Metal
Part II  Modeling of Sheet Metal Forming: In Memory of Prof. Jean-Claude Gelin
12  3D-Swivel-Bending—A Flexible and Scalable Forming Technology
13  A Comparative Study of Incremental Sheet Forming Process to Achieve Optimal Accuracy
14  A Virtual Laboratory Based on Full-Field Crystal Plasticity Simulations to Predict the Anisotropic Mechanical Properties of Advanced High Strength Steels
15  Development of a Numerical 3D Model for Analyzing Clinched Joints in Versatile Process Chains
16  Experimental and Finite Element-Based Analyses of FLCs for AA5052 and AA5083 Alloys
17  Finite Element and Experimental Investigation of Multi-stage Deep Drawing of Stainless Steel 304 Sheets at Elevated Temperature
18  Formability Analysis of Metal–Polymer Sandwich Composites Made of Al and PE Sheets Using Numerical Simulations
19  Numerical Modeling and Optimization of Fiber Metal Laminates
20  Investigation of the Effect of Blank Holding Force on Earing Defect During Circular Deep Drawing Process Through Finite Element Analysis and Experimentation Using AA6061 and Low-Carbon Steel Sheets
21  On the Generalized Plane-Strain Constraints for Orthotropic Plasticity Modeling of Sheet Metals
22  Springback Investigation of Advanced Path-Dependent Constitutive Models for Sheet Metal Forming
23  Stretch-Flanging Behavior of Dual-Phase Steel Using Single-Point Incremental Forming Process
24  Three-Dimensional Control Point Based Surface Description for Data Reduction, Reverse Engineering and Springback Compensation in Sheet Metal Forming
25  Time-Dependent Method for the Inverse Evaluation of Yield Locus Using Nakazima Experiments
Part III  Mechanics and Materials of Sheet Forming: In Honor of Thomas B. Stoughton
26  A Novel Testing Methodology for In Situ Microstructural Characterisation During Continuous Strain Path Change
27  Comparison of Experimental and Finite Element Analysis Results of a Car Body Part with the Optimization of Material Parameters
28  Draw Die Development to Maximize Aluminum Formability Potential for Making Styling Featured Outer Panels
30  Hydroforming Behaviour of TIG-Welded Tubes of Austenitic Stainless Steel
31  Influence of Kinematic Hardening on Clinch Joining of Dual-Phase Steel HCT590X Sheet Metal
32  Lightweighting Through Stiffening Dart Formation and Its Rigidity Evaluation
33  Modeling of the Anisotropic Evolution of Yield Surface Based on Non-associated Flow Rule
34  On Strain Hardening Modeling in Associated and Non-Associated Orthotropic Plasticity
35  Prediction of Ductile Fracture in Bainitic Steel with Dependence on Stress States and Loading Orientation
36  Shape Optimization of a Cruciform-Like Specimen for Combined Tension and Shear Loading
Part IV Machine Learning and Big Data
37  Data-Based Prediction Model for an Efficient Matching Process in the Body Shop
38  Deep Learning-Based Defect Inspection in Sheet Metal Stamping Parts
Part V Multiscale Modeling of Deformation and Fracture Behavior of Metallic Materials
39  Analysis of Damage and Fracture Mechanisms in Steel Sheets: Biaxial Experiments and Numerical Simulations
40  Damage Evolution in DP600 Sheets Using a Combined Finite Element—Cellular Automata Model
41  Deformation and Failure Behavior of Steel Under High Strain Rate and Multiaxial Loading
42  Forming–Structural-Coupled Analysis: The Method to Predict Die Deformation Using Quick Simulations
43  Investigating the Formability and Failure Mechanism of an Advanced High Strength Steel by a Microstructure-Based Hierarchy Modeling Approach
44  Investigation on the High Strain Rate Formability of Al-Cu-Mg Alloy by Solid–Liquid Coupling Simulation
45  Neutron Diffraction and Crystal Plasticity Analysis on Q&P Steel in Deformation
46  Predicting the Flow and Failure Properties of Dual-Phase Steel Using Phenomenological Models
Part VI Modelling of Thermo-Mechanical Sheet Forming
47  Development of a Hot Cutting Process for Functional Parts by Stress State-Dependent Damage Modeling
48  Impact of Thermal Conditions on Predicted Formability of TRIP Steels
49  Local Heat Treatment for Springback Reduction in Deep Drawing of  Advanced High-Strength Steel
50  Strain and Stress-Based Forming Limit Diagrams for Inconel 718 Alloy
51  Validation of Comprehensive Material and Friction Models for Simulation of Thermo-Mechanical Forming of High-Strength Aluminium Alloys Using HFQ Technology
Part VII Modelling of Failure
52  Development of a Modified Punch Test for Investigating the Failure Behavior in Sheet Metal Materials
53  Effect of Width/Thickness Effect of Sheet Metals on Bendability
54  Investigation of a Pre-strain-Specific Edge Crack Sensitivity Factor and Its Implementation in FEM
55  Prediction of Deformation and Failure Anisotropy for Magnesium Sheets Under Mixed-Mode Loading
56  Prediction of Necking Initiation in Case of Abrupt Changes in the Loading Direction
57  Strain Rate-Dependent Hardening Behavior of Weld Metal in Laser Welded Blanks with GEN3 AHSS
58  The Importance of the Choice of the Yield Criterion in Triaxiality Evaluation for Highly Anisotropic Zirlo Sheets
Part VIII Modelling of Friction
59  A Numerical Study of Local Elastic Tool Deformation in Sheet Metal Forming Simulation
60  Analysis and Evaluation of the Clamping Force on the Tool Surface During the Blanking Process
61
  Evaluating Lubricants for Warm Forming of Aluminum 6xxx Alloys
62  Implementation of Real Contact Areas Into Sheet Metal Forming Simulations Using Digital Spotting Images
63  Optimization of Slip Conditions in Roll Forming by Numerical Simulation
64  Surface Texture Design for Sheet Metal Forming Applications
Part IX Challenges and Opportunities in Forming Aluminum
65  Effect of Thermal Treatment on Deep Drawability of AA3xxx Alloy
66  Sensitivity Study of Plastic Anisotropy on Failure Prediction in Hole-Expansion
67  Dynamic Deformation Behaviour of Al-Li Alloys Under High Strain Rate Deformation
68  Research on Electric Current-Assisted Draw Bending of AA7075-T6 Sheet
Part X Other Topics
69  Numerical Modeling for Progressive Crushing of Composite and Hybrid Metal—Composite Structures
70  A New Sample for Oscillation-Free Force Measurement at High Strain Rates and Its Physical Principles
71  A Novel Benchmark Test for Validating the Modelling and Simulation Methodology of Modern Gas-Based Hot Sheet Metal Forming Processes
72  Analysis on Deformation Behavior of High-Strength Steel Using the Finite Element Method in Conjunction with Constitutive Model Considering the Elongation at Yield Point
73  Automatic Extraction and Conversion of the Bending Line from Parametric and Discrete Data for the Free-Form Bending Process
74  Characterization of Cohesive Zone Model Properties of Laminated Metal Sheet with a Thin Adhesive Layer
75  Clinching in In Situ CT—A Novel Validation Method for Mechanical Joining Processes
76  Design Guideline of the Bolt Hole Based on the Parametric Formability Analysis
77  Experimental and Numerical Evaluation of DP600 Fracture Limits
78  FE Simulations About the Influence of Work Hardening Derived from Embossing Process on Hole-Expansion of Duplex Embossed Sheet
79  Identification and Validation of Brass Material Parameters Using Single Point Incremental Forming
80  Improvement of the Strength of an Aluminum Liner by Beading Under Consideration of Internal Pressure and Low Temperatures
81  Influence of Loading Direction on the Mechanical Parameters of Pre-formed Materials in Tensile Test
82  Microstructure Modelling of the HEC Behaviour of a Novel Vanadium DP980 Cold Rolled Alloy
83  Numerical Description of the Physical Properties of Stretch Web Connectors in Progressive Die Stamping
84  Numerically Coupled Tools for Double-Sided Incremental Sheet Forming
85  Overcoming Major Obstacles of Springback Compensation by Nonlinear Optimization
86  Sheet Metal Forming Simulation System Strongly Coupled with Die Tool Deformation
Author Index
Subject Index