Surface Engineering

Front Matter....Pages i-xxii
Characterisation and Quality Control of Surface Treatments and Coatings....Pages 1-13
Microstructural Preparation and the Achievement of a Representative Surface....Pages 14-21
Photothermal Reflectance Investigation of Implanted Silicon....Pages 22-28
The Erosion-Corrosion of a Nitrocarburized Low Alloy Steel in a Simulated FBC Environment....Pages 29-38
Comparison of Fractal and Conventional Topographic Analysis of Electric Discharge Machined Ceramic Surfaces....Pages 39-51
Corrosion Protection through Salt Bath Nitriding....Pages 52-61
Protection of Surfaces of Natural Stone and Concrete through Polymers....Pages 62-71
The Influence of Directivity of Machining Marks on Grindability and Wear of Honed Surfaces....Pages 72-81
Wear Resistant Surfaces with a Hardphase Gradient....Pages 82-90
Surface Characterization and High-Temperature Adhesive Bonding of Carbon Fiber-Polyimide Matrix Composites....Pages 91-99
Contact Angles on Imperfect Solid Surfaces....Pages 100-112
Engineering the Interphase in Reinforced Plastics....Pages 113-119
Ferroelectric Thin Films from Metallo-organics: The Influence of Different Atmospheres during RTA Processing....Pages 120-125
Ultrasonic Verification of Surface Treatment Adequacy in Metal-to-Metal Adhesive Joints....Pages 126-135
The Unidirectional Tensile Characteristics of Ion-Nitrided and Ion-Carbonitrided Surface Layer of 40CrNiMo....Pages 136-145
Friction and Metal Transfer in Sliding Aluminum against Ion-Implanted Steel....Pages 146-155
The Effect of Ion Implantation on the Fretting Fatigue Properties of Titanium Alloy Fan and Compressor Blades....Pages 156-166
Martensitic Transformation in 304 Stainless Steel after Implantation with Neon....Pages 167-176
Elevated Temperature Ion Implantation: A New Direction for Surface Engineering....Pages 177-187
Surface Modification Experiment by Intense Pulsed Ion Beam....Pages 188-197
PSII Nitrogen Implanted M2 Tool Steel for Wear Resistance in Wood Machining Tools....Pages 198-207
Plasma Nitriding and Nitrocarburizing of Austempered S.G. Cast Iron....Pages 208-217
Techniques for Improved Surface Integrity of Aerospace Aluminum Alloys....Pages 218-227
Duplex Hardening: An Advanced Surface Engineering Technique for Helicopter Transmissions....Pages 228-237
Low Cycle Fatigue Fracture Behaviour of Conventional and Damage Tolerant Microstructures of Inconel 718 at 650°C....Pages 238-251
Corrosion and Wear Protection of Compressor Blades by Aluminum Coatings and a New Method for Testing their Erosion Resistance....Pages 252-259
Effects of Surface Finish on the Solid State Welding of High Strength Aircraft and Aerospace Aluminium Alloys....Pages 260-269
Surface Modifications of Zirconium Alloys by Laser Glazing....Pages 270-279
Laser Shock Hardening of Welded Maraging Steel....Pages 280-290
Laser Surface Heat Treatment Used for Induction of Residual Stresses into Circular Saw Blades for Better Working Behaviour....Pages 291-302
Residual Stress Evaluation of Materials Manufactured by High-Energy Process....Pages 303-312
Finite Element Analysis of Main Crack-Microcrack Interaction under Mode-I Loading....Pages 313-324
The Effect of Surface Treatments on the Fretting Wear of an Aluminium Alloy (RR58)/Steel (BS 970 080 M40) Couple....Pages 325-334
Degradation of a Biomedical Polyurethane: Surface Integrity and Fatigue Effects....Pages 335-343
Microstructural and Surface Effects on Fatigue of Ti-6Al-4V Alloy....Pages 344-353
Corrosion and Wear Characteristics of Nickel Aluminide, NiAl, in NaCl Medium....Pages 354-360
The Study of Anticorrosion Technique for Natural Gas Processing Plants....Pages 361-370
Shot Peening—Current Trends, Future Prospects....Pages 371-378
Shot Peen Controls and Aircraft Engine Requirements....Pages 379-385
Fatigue Fracture and Residual Stress Relaxation in Shot-Peened Components....Pages 386-392
Some Theoretical Problems of Shot Peening....Pages 393-403
Fatigue Damage Evaluation of Shot Peened High Strength Aluminum Alloy....Pages 404-416
Effect of Shot Peening Process Controls on Consistent Treatment....Pages 417-427
Effect of Pre- and Post-Processing upon Shot-Peening Residual Stresses....Pages 428-442
Surface Kinetics of Hydrogen Entry into Zirconium Films....Pages 443-455
Abrasive Flow Machining for Automatic Surface Finishing and Capacitance Technology for In-Process Surface and Dimensional Metrology....Pages 456-467
Evolution du Dommage Surfacique au Cours d’un Essai de Fatigue Oligocyclique: Comparaison avec des Mesures de Dommage Volumique....Pages 468-477
The Influence of Fine Structure, Morphology and Composition of Alloy and Oxide on the Growth of Cr 2 O 3 Scales....Pages 478-489
Effect of Surface Texture Geometry on the Dynamic Performance of Hydrostatic Bearings....Pages 490-503
Study of Tools for Hot Rolling of Steel Alloy Tubes....Pages 504-515
Quality of Surface Coating by Submerged Arc Welding....Pages 516-527
Surface Degradation and Stress Corrosion Cracking of Bronze in Moist Oil....Pages 528-537
On Magnetron Sputtered Gradient and Multilayer Coatings....Pages 538-547
Hydrophobic Reorientation of Glow-Discharge Treated Polyethylene as Measured by Contact Angles....Pages 548-554
Hall Effect and Resistance Measurements on Implanted and Annealed Silicon Layers....Pages 555-561
Diffusion of Carbon in Carbon Steels and Graphitic Cast Irons Heat Treated by Concentrated Energy Sources....Pages 562-571
Influence of Electrochemical Honing Methods on Load Capacity of Surfaces....Pages 572-581
Evaluation of Acid Rain Resistant Clear Coatings for Stone Structures....Pages 582-591
Computer Modelling of the Abrasive Flow Machining Process....Pages 592-601
Theoretical and Practical Study of On-Line Identification for the Grinding Burn....Pages 602-614
Sand Erosion and Cavitation Behaviour of Hydraulic Turbine Runner Materials....Pages 615-624
Improvement of Fatigue Resistance of Steel Parts after Various Surface Treatments....Pages 625-639
Relationship between Ductility and Wear Resistance of High Mn-Steels....Pages 640-651
The Use of Shot Peening as a Surface Preparation Treatment for the Electrodeposited Chromium Plating....Pages 652-661
Analytical Solutions of Crack Developing at Rail Joint Due to Impacting....Pages 662-667
An Investigation into Surface Generation during Machining High Strength Low Alloy Steel....Pages 668-677
Development of Finish Turning Inserts: Present Trends and Future Prospects....Pages 678-687
Machining Residual Stresses....Pages 688-699
Effect of Cold Deformation on Boronizing Processes and Wear Behavior of Low Carbon Steel 1020....Pages 700-709
Back Matter....Pages 711-712