Solutions for Sustainable Development-Proceedings of the 1st International Conference on Engineering Solutions for Sustainable Development (ICESSD 2019), October 3-4, 2019, Miskolc, Hungary

Part A: Process Engineering, Modelling and Optimisation
Analytical and numerical study for minimum weight sandwich structures 
A. Al-Fatlawi, K. Jármai & G. Kovács
Estimation of compressive strength of current concrete materials: Effect of core diameter and maximum aggregate size 
M.E. Belgacem, A. Brara & A. Ferdjani
The effect of the gear wear for the contact ratio 
J. Bihari
Determination of GTN parameters using artificial neural network for ductile failure 
Y. Chahboub, S. Szabolcs & H. Aguir
Investigating three learning algorithms of a neural networks during inverse kinematics of robots 
H.M. Ghafil, L. Kovács & K. Jármai
Prediction of distillation plate’s efficiency 
V. Kállai, P. Mizsey & L.G. Szepesi
CAD tools for knowledge based part design and assembly versioning 
K. Nehéz, P. Mileff & O. Hornyák
Heat transfer analysis for finned tube heat exchangers 
M. Petrik, L.G. Szepesi & K. Jármai
Effect of soil reinforcement with stone columns on the behavior of a monopile foundation subjected to lateral cyclic loads 
S.A. Rafa, I. Rouaz & A. Bouaicha
Performance of Cold Formed Steel Shear Wall Panel with OSB Sheathing under lateral load 
I. Rouaz, S. Rafa & A. Bouaicha
The use of the linear sliding wear theory for open gear drives that works without lubrication 
F. Sarka
Numerical simulation methods of stress corrosion cracking 
B. Spisák, Z. Siménfalvi, Sz. Szávai & Z. Bézi
Implementation of a customized CAD extension to improve the calculation of center of gravity 
M. Szabó, P. Mileff & K. Nehéz
 
Part B: Sustainable and Renewable Energy and Energy Engineering
Towards CHP system: Preliminary investigation and integration of an ORC cycle on a simple gas boiler 
M. Amara, H. Semmari & A. Filali
Examination the effect of environmental factors on a photovoltaic solar panel 
I. Bodnár, L.T. Tóth, J. Somogyiné Molnár, N. Szabó, D. Erdősy & R.R. Boros
Thermal behaviour of PCM-gypsum panels using the experimental and the theoretical thermal properties-Numerical simulation 
F. Boudali Errebai, S. Chikh, L. Derradji, M. Amara & A. Terjék
Experimental and numerical study of the thermal behavior of a building in Algeria 
L. Derradji, F. Boudali Errebai, M. Amara. A. Limam & A. Terjék
Comparison of Sakiadis and Blasius Flows using Computational Fluid Dynamic 
M.M. Klazly & G. Bognár
Techniques for evaluation of mixing efficiency in an anaerobic digester 
B. Singh, Z. Szamosi & Z. Siménfalvi
Part C: Waste Management and Reverse Logistics
Vehicle routing in drone-based package delivery services 
A. Agárdi, l. Kovács & T. Bányai
Cyber-physical waste collection system: a logistics approach 
M.Z. Akkad & T. Bányai
Efficiency improvement of reverse logistics in Industry 4.0 environment 
I. Hardai, B. Illés & Á. Bányai
Application of sigmoid curves in environmental protection 
F.J. Szabó
Part D: Environmental Management and Ecodesign
Comparative study of the influence of traditional walls with different typologies and constructive techniques on the energy performance of the traditional dwellings of the Casbah of Algiers 
H.F. Arrar, A. Abdessemed Foufa & D. Kaoula
Rules of environmentally friendly packaging 
Á. Takács
 
Part E: Circular Economy and Life Cycle Approaches
Aluminium infinite green circular economy – theoretical carbon free infinite loop, combination of material and energy cycles 
N. Babcsán
Life Cycle approach of a new Industrial Symbiosis alternative 
B.S. Gál, R.S. Bodnárné & Zs. István
Possibilities for adopting the circular economy principles in the EU steel industry 
Á. Kádárné Horváth, M. Kis-Orloczki & Á. Takácsné Papp
Influence of urban morphology on the environmental impactsof district. Applied LCA 
D. Kaoula & A. Abdessemed Foufa
Life cycle extension of damaged pipelines using fiber reinforced polymer matrix composite wraps 
J. Lukács, Zs. Koncsik & P. Chován
Innovative solutions for the building industry to improve sustainability performance with Life Cycle Assessment modelling 
V. Mannheim, Zs. Fehér & Z. Siménfalvi
Investigation of different foam glasses with Life Cycle Assessment method 
A. Simon, K. Voith & V. Mannheim
Circular economy solutions for industrial wastes 
K.T. Szita, Zs. István, R.S. Bodnárné & A. Zajáros
New approach for characterizing the “naturalness” of building materials 
A. Velősy
Part F: Smart Manufacturing and Smart Buildings
Grouping and analyzing PLC source code for smart manufacturing 
O. Hornyák
Environmental assessment of buildings in Sudan 
S.A.A. Ismail & Zs. Szalay
Part G: Innovation and Efficiency
The innovation shell, and barriers of disruptive innovation 
Z. Bartha & A.S. Gubik
Lifetime analyses of S960M steel grade applying fatigue and fracture mechanical approaches 
Zs. Koncsik
Efficient application of S690QL type high strength steel for cyclic loaded welded structures 
H.F.H. Mobark & J. Lukács
Improvement of the modern house’s energy efficiency in the regionof In Saleh 
S. Oukaci, A. Hamid, D. Sammar, S. Sami & A. Naimi
Innovative and efficient production of welded body parts from 6082-T6 aluminium alloy 
R.P.S. Sisodia & M. Gáspár
Redundancy Analysis of the Railway Network of Hungary 
B.G. Tóth
Part H: Earth Science
A short discussion on some influencing factors of an artificial corrosion system and obtained metallic pipe samples 
H.D. Thien, B. Kovács, T. Madarász & I. Czinkota