CCNP ONT portable command guide

Cover......Page 1
Contents......Page 11
Introduction......Page 16
 Cisco Service-Oriented Network Architecture......Page 20
 Cisco Enterprise Composite Network Model......Page 21
Chapter 2 Cisco VoIP Implementations......Page 22
  Moving Cisco Unified CME Files to the Router Flash......Page 23
 Basic Manual CME Setup Using the CLI......Page 24
  Configuring DHCP for the VoIP Phones......Page 25
  Defining a DHCP Relay......Page 26
  Creating Phones......Page 27
 CME Auto Configuration Using the CLI......Page 28
 Installing IP Communicator......Page 30
 Changing Codecs Using the CLI......Page 39
 Router Configuration......Page 40
 Using Modular QoS CLI (MQC) for Implementing QoS......Page 44
  Step 1: Defining Traffic Classes Using the class-map Command......Page 45
  Step 2: Defining Policies for the Traffic Classes Using the policy-map Command......Page 46
  Step 3: Applying the Defined Policies Using the service-policy Command......Page 47
  Configuration Example: Enforcing a Sub-Rate......Page 48
 Implementing QoS Using AutoQoS......Page 50
 Implementing QoS with Cisco Security Device Manager (SDM) QoS Wizard......Page 51
  Monitoring QoS Status with Cisco SDM......Page 55
 Networked-Based Application Recognition (NBAR) for Classification......Page 58
 Classification and Marking......Page 59
  Step 2: Choose the Interesting Traffic......Page 60
  Step 5 (repeated): Mark the Traffic in the Class......Page 62
 Configuring Priority Queuing (PQ)......Page 63
  Step 3: Optionally Establish the Packet Limit for Each Queue......Page 64
 Configuring Custom Queuing (CQ)......Page 65
 Configuring PQ & CQ for Frame Relay......Page 67
  Step 4: Create a Map Class to Call the Priority List and/or Custom Queue List......Page 68
 Configuring Weighted Fair Queuing (WFQ)......Page 69
 Configuring Class-Based Weighted Fair Queuing (CBWFQ)......Page 72
  Step 4: Add Class Maps to the Policy......Page 73
  Step 5: Apply Guaranteed Bandwidth and Maximum Packet Limits for Each Class......Page 74
  Step 8: Verify Policy Configuration......Page 75
 Configuring Low-Latency Queuing (LLQ)......Page 76
  Step 3: Add Class Maps to the Policy and Specify One (or More) Class(es) with Priority Bandwidth......Page 77
  Step 5: Verify Policy Configuration......Page 78
 Configuring Low-Latency Queuing (LLQ) with Class-Based Weighted Random Early Detection (CBWRED)......Page 79
  Step 3: Add Class Maps to the Policy and Specify One (or More) Class(es) with Priority Bandwidth......Page 80
  Step 5: Verify Policy Configuration......Page 82
  Single Token Bucket/Single Rate......Page 83
  Two Token Bucket/Two Rate......Page 85
  Per-Interface Traffic Shaping......Page 87
  Class-Based Traffic Shaping......Page 88
 Implementing QoS Preclassify......Page 89
 Forms of AutoQoS......Page 92
 Frame Relay DLCI and ATM Restrictions......Page 93
 Router Prerequisites......Page 94
  Step 1: Auto Discovery......Page 95
 Deploying AutoQoS on IOS-Based Catalyst Switches......Page 96
  Command 2: Enabling AutoQoS on Ports That Are Connected to Other Trusted Devices Such as Routers and Switches......Page 97
 Verifying Cisco AutoQoS on the Switch......Page 98
 Flowchart for Verifying and Modifying AutoQoS-Generated Configurations......Page 99
 Wireless LAN QoS Configuration Using the GUI......Page 100
 Configuring Encryption and Authentication on Lightweight Access Points......Page 106
  Configuring Open Authentication......Page 108
  Configuring Static WEP Authentication......Page 109
  Configuring WPA with PSK......Page 110
  Configuring Web Authentication......Page 111
  Configuring 802.1x Authentication......Page 113
 Cisco Wireless Control System (WCS)......Page 115
  WCS Summary Pages......Page 116
  Adding a Cisco Wireless LAN Controller......Page 118
  WCS Maps—Adding a Campus Map......Page 121
  WCS Maps—Adding a New Building......Page 124
  Rogue Access Point Detection......Page 126
Appendix: Create Your Own Journal Here......Page 128