Advances in Surface Treatments. Technology–Applications–Effects

Content: 
Other Pergamon titles of interest, Page ii
Front Matter, Page iii
Copyright, Page iv
INTERNATIONAL EDITORIAL ADVISORY COMMITTEE FOR THIS VOLUME, Page v
EDITORIAL, Pages vi-vii
MAIN AREAS COVERED IN THE SERIES, Pages viii-ix
INDUSTRIAL COMMITTEE AND SUPPORT GROUP, Page x
INSTRUCTIONS TO CONTRIBUTORS, Pages xi-xii
CONVERSION UNITS, Page xvi
SURFACE LAYER CHARACTERISTICS AND CORROSION RESISTANCE OF NITRIDE AND NITROCARBURIZED CARBON STEELS, Pages 3-15
NON-LINEAR THERMAL PROBLEMS IN PROGRESSIVE INDUCTION HARDENING, Pages 17-29
RESIDUAL STRESSES CAUSED BY THERMAL AND THERMOCHEMICAL SURFACE TREATMENT, Page 31
SOME EXPERIENCES GAINED WITH PLASMA AND GAS NITRIDED 42Cr Mo4 STEEL CRANKSHAFTS, Pages 33-45
PREVISION DE LA MICROSTRUCTURE DES COUCHES OBTENUES PAR CARBONITRURATION ET TREMPE, Pages 47-57
CONTRIBUTION OF PROGRESSIVE INDUCTION TO THE CONTROLLED HARDENING TREATMENT OF STEELS FOR COLD ROLLING, Pages 59-74
FATIGUE STRENGTH CHARACTERISTICS OF Cr-Mn-Ti STEEL AFTER CEMENTATION AND CARBON-NITROGEN HARDENING, Pages 75-83
ETUDE ET OPTIMISATION DE LA PHOSPHATATION AU ZINC EN LABORATOIRE, Pages 85-92
STRUCTURAL AND PHYSICOCHEMICAL FACTORS CONTROLLING THE FORMATION OF CHROMIUM CARBIDE CASES DURING CHROMIZING, Pages 93-110
COMPRESSIVE PRE-STRESSING USING NEW PERCUSSION APPARATUS, Pages 113-121
ABRASIVE FLOW MACHINING: A PROCESS FOR SURFACE FINISHING AND DEBURRING OF WORKPIECES WITH A COMPLICATED SHAPE, Pages 123-138
BEHAVIOR OF SURFACE RESIDUAL STRESS INDUCED BY SHOT PEENING (II), Pages 139-144
THE EFFECT OF SHOT-PEENING INTENSITY ON THE FATIGUE AND FRETTING-FATIGUE BEHAVIOUR OF AN ALUMINIUM ALLOY, Pages 145-153
OVERVIEW ON THE SHOT PEENING PROCESS, Pages 155-170
A MODEL FOR THE DEVELOPMENT OF RESIDUAL STRESSES IN GRINDING, Pages 173-189
ADAPTIVE CONTROL IN GRINDING. WHY AND HOW, Pages 191-207
A PROCEDURE FOR SETTING UP EXACTLY THE EQUIPMENT FOR THE GRID PROJECTING TYPE MOIRé METHOD, Pages 209-215
MEASUREMENT OF RESIDUAL STRESS DISTRIBUTION BY THE INCREMENTAL HOLE-DRILLING METHOD, Page 217
COMPUTER CODE FOR TRI-AXIAL X-RAY STRAIN AND STRESS ANALYSIS USING FITTED CURVES, Pages 219-226
INFLUENCE OF GRINDING AND CAVITATION ON SURFACE INTEGRITY OF STAINLESS STEEL, Pages 229-237
MAGNETABRASIVE FINISHING: A METHOD FOR THE MACHINING OF COMPLICATED SHAPED WORKPIECES, Pages 239-256
ALUMINIUM PLATING BY SIMPLEX METHOD USING PULSE RECTIFIER CURRENT, Pages 259-270
CRITERIA FOR THE CHOICE OF A PVD TREATMENT FOR THE SOLUTION OF WEAR PROBLEMS, Pages 271-294
RESULTATS ET EXEMPLES D'APPLICATIONS INDUSTRIELLES DES PROCEDES: SURSULF ET OXYNIT, Pages 295-320
HOW TO CHOOSE COATINGS IN FRETTING, Pages 321-334
IMPACT EROSION KINETICS ON A HARDENED SURFACE COATED WITH A SOFT MATERIAL, Pages 335-354
THE PROTECTION OF THIN STEEL SHEET BY PASSIVATION AND COATING WITH POLYMERS, Pages 355-363
SURFACE FINISH IN LASER MATERIALS PROCESSING, Pages 367-374
RELATIVE EFFECTS ON SURFACES AND SUB-SURFACES AT DIFFERENT LASER WAVE LENGTHS, Pages 375-379
SURFACE TREATMENT OF MATERIALS USING HIGH POWER LASERS, Pages 381-408
FRICTION AND WEAR OF LASER TREATED ALUMINIUM-SILICON ALLOYS, Pages 409-423
ILAFT/FKJA SYSTEM FOR SURFACE FINISHING WASTEWATER TREATMENT, Pages 427-439
INDUSTRIAL COMPRESSED BREATHING AIR PURIFICATION, Pages 441-450
IMPROVING CORROSION AND WEAR RESISTANCE BY SALT BATH NITROCARBURIZING PLUS OXIDIZING IN AUTOMATED FACILITIES, Pages 451-467
JET KOTE: A New Thermal Spraying Technique for the Protection of Turbine Blades against Erosion, Pages 469-522